Products > Kits>Eagle Dual Pressurized Above Dash HUD Kit
KIT FEATURES
The Pressurized Dual Eagle kit has two chevron style displays and two HUD adapters. With the chevron display, when you come in for a landing you want to fly to the blue donut (on speed for landing). Should you come in with too low of an angle of attack, the yellow chevron will light up and tell you to put your nose up. Should you come in with too high of an angle of attack, the red chevron will light up and tell you nose down.
- Instantaneous Angle of Attack indication.
- Additional indication segments.
- Three point calibration process, programmed on remote switch panel, to aircraft specific lift curve.
- 16 different LED brightness levels from ultra dim to very bright.
- Display has an imbedded photocell for daytime/nighttime brightness settings, choice of which is programmed at the display.
- Audio output, tied to existing audio input on audio panel by others.
- 4 different audio options to choose from which is programmed by the end user at the remote switch panel.
- Audio mute switch with amber LED indicator located on remote switch panel.
- 12-28 VDC input draws less than 0.250 Amps at full brightness.
HUD FEATURES
The HUD is a self contained adjustable beam splitter adapter that mounts to the lip of the Eagle display and turns the Alpha System AOA into a true HUD. Intended for placement directly within the pilot's peripheral vision. Allows for instantaneous viewing of AOA information exactly where needed. The HUD glass is an enhanced color correcting, anti-glare lens. Comes complete with mounting frame, bezel, display brackets and hardware.
- Frame Dimensions: L: 4 1/8", W: 1.250"
- Bezel Dimensions: L: 4" x W: 2.5"
HUD COMPONENTS
- Mounting Frame.
- Dash Bezel.
- Tinted Lens.
- Custom Display Brackets.
- Hardware.
- HUD Cover with Flag.
Dual HUD Pressurized Kit Part #: DSTR-AOA-9600DPK-(HUD)
KIT COMPONENTS
|
|
ADAPTER KITS / ADD ONS
- I/O Module Enhancement (Flaps)
- Heated Probes12V / 24V
ARTICLES
TECHNICAL SPECIFICATIONS
| Complete Kit Weight | Less than 3.00 lbs. Click here for full list. | |
| Flush Mount HUD Frame Dimensions | L: 4 1/8", W: 1.250" | |
| Flush Mount HUD Bezel Dimensions | L: 4" x W: 2.5" | |
| AOA Interface Module size | In Inches: 5.75 x 2.60 x 1.65 | |
| System Voltage Requirements | 12 - 28 Volts DC | |
| System Max Power Draw | 0.250 Amps | |
| System Power Cable | 6 ft, three wires: power, ground and shield | |
| Heated Probe Voltage Requirements | 12 or 24 VDC (must specify when ordering) | |
| Heated Probe Power Draw | 86 Watts at 12VDC / 172 Watts at 24VDC | |
| Heated Probe Current Draw | 8 Amps at 12VDC and 8 Amps at 24VDC | |
| Heated Probe Power Wire | Supplied by others | |
| Audio Output | 1 Volt P-P max at 300 ohm input impedance | |
| Aux (Audio) Cable | 6 ft, three wires: AP audio, AP ground and shield | |
| Audio Options | Four | |
| Mute Switch | Yes, on switch panel | |
| LED Brightness Levels | 16, from ultra dim to very bright | |
| Photocell Diode | On display, allows for custom daytime/nighttime brightness settings | |
| Pressurized Version | Yes | |
TECHNICAL DRAWINGS & DIAGRAMS
| Dual Pressurized Connection Diagram | Download |
| Dual Pressurized Wiring Diagram | Download |
| Display Dimensions | Download |
| Increasing AOA Diagram | Download |
| Eagle Lift Curve | Download |
| Display Segment Transitions | Download |
| HUD Dimensions | Download |
| HUD Base Plate Dimensions | Download |
| Power Cable | Download |
| Switch Panel Cable | Download |
| IF Module Extension Cable | Download |
| IF Module AUX Cable | Download |
| Dual IF Module Cable | Download |
| Standard Probe Mounting Plate | Download |
-Dual-Eagle-Connection-Diagram-Rev-E-small-web.jpg)
-Dual-Eagle-Connection-Diagram-Rev-E-large-web.jpg)
Videos
G36 Bonanza Flying AOA |
Slow Flight Emergency Landing |
Eagle Display Transitions |
|
Address: 1600 Old Sims Rd NW
Cedar, MN 55011
Phone: 763-506-9990
Email: flysafe@alphasystems-usa.com
