Products > Kits>Eagle Pressurized Kit
KIT FEATURES
The Eagle pressurized AOA kit was designed and comes complete with most parts to mount the AOA sense probe, connection hoses and AOA sensor module outside of the pressure bulkhead. The AOA sensor connects through to the inside cockpit through unused pins on an existing pass-through connector. Connections on the inside of the aircraft connect the signals to the display interface module for power, audio, and display connections. Our systems are designed for simple installation and pilot flown calibration for real time, instantaneous full-scale AOA range.
The Eagle display is a highly visible, full color, chevron style display. With the chevron display, when you come in for a landing you want to fly to the blue donut (on speed for landing). Should you come in with too low of an angle of attack, the yellow chevron will light up and tell you to put your nose up. Should you come in with too high of an angle of attack, the red chevron will light up and tell you nose down.
- Instantaneous Angle of Attack indication.
- Additional indication segments.
- Three point calibration process, programmed on remote switch panel, to aircraft specific lift curve.
- 16 different LED brightness levels from ultra dim to very bright.
- Display has an imbedded photocell for daytime/nighttime brightness settings, choice of which is programmed at the display.
- Audio output, tied to existing audio input on audio panel by others.
- 4 different audio options to choose from which is programmed by the end user at the remote switch panel.
- Audio mute switch with amber LED indicator located on remote switch panel.
- 12-28 VDC input draws less than 0.250 Amps at full brightness.
Standard Kit Part #: DSTR-AOA-9600PK
KIT COMPONENTS
|
|
FIXED / SWIVEL MOUNT COMPONENTS
|
ADAPTER KITS / ADD ONS
- I/O Module Enhancement (Flaps)
- Heated Probes12V / 24V
TECHNICAL SPECIFICATIONS
| Complete Kit Weight | Less than 3.00 lbs. Click here for full list. | |
| Vertical Fixed Mount Weight | Approximately .12 LBs | 2 oz | |
| Vertical Swivel Mount Weight | Approximately .195 LBs | 3.1 oz | |
| AOA Interface Module size | In Inches: 5.75 x 2.60 x 1.65 | |
| System Voltage Requirements | 12 - 28 Volts DC | |
| System Max Power Draw | 0.250 Amps | |
| System Power Cable | 6 ft, three wires: power, ground and shield | |
| Heated Probe Voltage Requirements | 12 or 24 VDC (must specify when ordering) | |
| Heated Probe Power Draw | 86 Watts at 12VDC / 172 Watts at 24VDC | |
| Heated Probe Current Draw | 8 Amps at 12VDC and 8 Amps at 24VDC | |
| Heated Probe Power Wire | Supplied by others | |
| Audio Output | 1 Volt P-P max at 300 ohm input impedance | |
| Aux (Audio) Cable | 6 ft, three wires: AP audio, AP ground and shield | |
| Audio Options | Four | |
| Mute Switch | Yes, on switch panel | |
| LED Brightness Levels | 16, from ultra dim to very bright | |
| Photocell Diode | On display, allows for custom daytime/nighttime brightness settings | |
| Pressurized Version | Yes | |
TECHNICAL DRAWINGS & DIAGRAMS
| Pressurized Connection Diagram | Download |
| Pressurized Wiring Diagram | Download |
| Display Dimensions | Download |
| Increasing AOA Diagram | Download |
| Eagle Lift Curve | Download |
| Display Segment Transitions | Download |
| Power Cable | Download |
| Switch Panel Cable | Download |
| IF Module Extension Cable | Download |
| IF Module AUX Cable | Download |
| Standard Probe Mounting Plate | Download |
-Eagle-Connection-Diagram-Rev-E-small-web.jpg "Pressurized Eagle Connection Picture")
-image-4-small-web.jpg "Eagle Display Installed in a Beechcraft Bonanza A36")
-Eagle-Connection-Diagram-Rev-E-large-web.jpg "Pressurized Eagle Connection Picture")
-image-4-large-web.jpg "Eagle Display Installed in a Beechcraft Bonanza A36")
Videos
Eagle Calibration |
Aeronca O-58B |
Yak 52 Install |
Piper PA46-350P-Mirage |
1940 Piper J-3 "Cub" |
Yak 52 Flying |
Yak 52 Rolls |
Piper PA46 Mirage Ridealong |
PA46 Magnetic Interference Test |
Mooney M20R |
Mooney M20J |
Kolb Flyer SS |
Mitsubishi MU-2B-26A |
Eagle Display Transitions |
Address: 1600 Old Sims Rd NW
Cedar, MN 55011
Phone: 763-506-9990
Email: flysafe@alphasystems-usa.com
